講演抄録/キーワード |
講演名 |
2020-03-06 16:35
直流アーク放電の磁気吹き消し効果への磁束密度と開離速度の影響 ○山内大輝・渡辺隼斗・澤 孝一郎・吉田 清(日本工大) EMD2019-71 エレソ技報アーカイブへのリンク:EMD2019-71 |
抄録 |
(和) |
直流コンタクトを用いて開離時アークを発生させ、磁石を電気接点の中心になるように設置し磁界を発生させた状態で、アーク継続時間ta、アークエネルギーEa等のアークの諸特性を測定し、磁気吹き消し効果の影響を確認した。電源電圧はDC100Vとし、閉成時電流I_0は0.5~30Aの範囲で変化させた。電気接点材料はタングステン(W)と銀(Ag)を用いた。磁束密度を0mT,5mT、および10mTとし、電気接点の開離速度を25mm/s,50mm/s、および100mm/sで変化させた。その結果、磁束を印加すると、印加していない時と比べてtaは大幅に短くなることが確認できた。また、一定の電流値以下になるとtaが長くなることを確認した。開離速度を遅くすると、taは長くなる傾向があった。電気接点材料による影響はAgの方がWに比べて、taが長くなることが確認できた。そして、EaはI_0が小さい時に大きくなることもあるが基本的には電流値の大きさに依存していることがわかった。 |
(英) |
The arc duration time ta and the arc energy Ea when a magnetic flux was applied to the electrical contact were measured. The effect of the magnetic blow-out was confirmed from the experimental results. The experimental conditions were as follows: the power supply voltage was DC100V, and the closing current Io was varied in the range of 0.5 to 30A. Electrical contact materials were tungsten (W) and silver (Ag). The magnetic flux density was set to 0 mT, 5 mT, and 10 mT, and the opening speed of the electrical contact was set to 25 mm/s, 50 mm/s, and 100 mm/s.
As a result, ta was short when the magnetic flux was applied, while it was significantly long without the magnetic flux. However, it was confirmed that ta when the magnetic flux was applied becomes longer when Io is small. Therefore, it was presumed that the effect of magnetic blowing was reduced when the current was small. Furthermore, when the breaking speed was low, ta became longer |
キーワード |
(和) |
磁気吹き消し / 電気接点 / アーク継続時間 / アークエネルギー / 磁束密度 / 開離速度 / / |
(英) |
Magnetic Blowout / Electrical Contacts / Arc Duration / Arc Energy / Magnetic Flux Density / Breaking Speed / / |
文献情報 |
信学技報, vol. 119, no. 466, EMD2019-71, pp. 61-64, 2020年3月. |
資料番号 |
EMD2019-71 |
発行日 |
2020-02-28 (EMD) |
ISSN |
Print edition: ISSN 0913-5685 Online edition: ISSN 2432-6380 |
著作権に ついて |
技術研究報告に掲載された論文の著作権は電子情報通信学会に帰属します.(許諾番号:10GA0019/12GB0052/13GB0056/17GB0034/18GB0034) |
PDFダウンロード |
EMD2019-71 エレソ技報アーカイブへのリンク:EMD2019-71 |