講演抄録/キーワード |
講演名 |
2017-04-20 14:45
インクジェット印刷法を用いた酸化銅(I)抵抗体の作製 ○松村 叡・泉 小波・吉田泰則・松井弘之・熊木大介・時任静士(山形大) ED2017-4 エレソ技報アーカイブへのリンク:ED2017-4 |
抄録 |
(和) |
本研究は、インクジェット印刷ではこれまで実現できなかった高抵抗の抵抗体を作製するため酸化銅(Ⅰ)に着目した。インクジェット印刷した銅ナノ粒子を最適条件で大気焼成することで、高抵抗率かつばらつきの小さい酸化銅(Ⅰ)薄膜を得ることに成功した。得られた酸化銅(Ⅰ)薄膜を用いて作製した印刷型酸化銅(Ⅰ)抵抗素子は、これまでインクジェット印刷型抵抗素子では困難であった1 MΩ以上の高抵抗範囲(1 MΩ ~ 15 MΩ)を、市販のチップ抵抗と同じ2.5 mm × 5 mmと小さい面積で実現できた。また、作製した抵抗素子の高周波特性は市販の抵抗素子と同等かそれ以上であった。本研究結果は、受動素子を含めたプリンテッドエレクトロニクスによる集積回路の実現に向け大きく貢献できる成果である。 |
(英) |
In this research, we focused copper (I) oxide in order to fabricate high resistance resistors which could not be realized by ink jet printing so far. We succeeded in obtaining copper (I) oxide thin film with high resistivity and small variability by sintering copper nanoparticles printed by inkjet under the optimum condition in the air. The resistive elements of the printed copper (I) oxide thin films had a high resistance range (1 M$ohm$ ~ 15 M$ohm$) which was difficult to achieve with conventional inkjet printed resistive elements. The size of the printed resistors was 2.5 mm × 5 mm which was equal to the size of commercially available chip resistors. In addition, the high-frequency characteristics of the fabricated resistive elements were equal to or better than those of commercially available resistive elements. We believe that these results can greatly contribute to realization of integrated circuits by printed electronics including passive elements. |
キーワード |
(和) |
プリンテッドエレクトロニクス / インクジェット印刷法 / 高抵抗体 / 銅ナノ粒子 / 酸化銅(Ⅰ) / / / |
(英) |
Printed Electronics / ink-jet printing method / high resistance resistor / Copper nanoparticles / Copper (I) oxide / / / |
文献情報 |
信学技報, vol. 117, no. 6, ED2017-4, pp. 13-16, 2017年4月. |
資料番号 |
ED2017-4 |
発行日 |
2017-04-13 (ED) |
ISSN |
Print edition: ISSN 0913-5685 Online edition: ISSN 2432-6380 |
著作権に ついて |
技術研究報告に掲載された論文の著作権は電子情報通信学会に帰属します.(許諾番号:10GA0019/12GB0052/13GB0056/17GB0034/18GB0034) |
PDFダウンロード |
ED2017-4 エレソ技報アーカイブへのリンク:ED2017-4 |