講演抄録/キーワード |
講演名 |
2023-05-19 13:00
管軸分岐端子をオフセット配置した小型OMT ○湯川秀憲・関 竜哉・深沢 徹・稲沢良夫(三菱電機) MW2023-17 |
抄録 |
(和) |
衛星通信用導波管給電回路において、異なる周波数帯の直交する直線偏波を分離するOMT(Ortho-Mode-Transducer)の小型化は開発課題のひとつである。しかしながら、OMTを小型化するため、各直線偏波を分離して出力する分岐端子の変成部を近接配置した場合、相互の影響により良好な特性が得られにくい問題がある。そこで、ここでは、直交する2つの直線偏波を伝送する円形導波管共通端子と、管軸方向に高周波数帯の直線偏波を分離する長方形分岐端子(管軸分岐端子)、管軸と直交する方向に低周波数帯の直線偏波を分離する長方形分岐端子(直交分岐端子)を有するOMTにおいて、小型化と良好な特性を両立する構成を提案する。
提案する構成は円形導波管を概略十字形状の導波管に変換し、管軸分岐端子は概略十字形状導波管の断面を階段状に変成、直交分岐端子は円形導波管と概略十字形状導波管の変換部をまたぐように直結して概略十字形状導波管の断面内で変成することにより小型化するものである。さらに、管軸分岐端子を共通端子の中心から直交分岐端子側にオフセットして配置することにより、変成部の近接配置の影響を補償して良好な特性の実現を図っている。
本提案構成について低周波数帯比帯域幅12.9%、高周波数帯比帯域幅3.5%で設計し、3Dプリンタ(Si含有率の低いアルミ合金)を用いて試作評価をしたところ、設計結果と測定結果は概ねよく一致し、反射25dB、アイソレーション30dB、XPD30dB、損失0.1dBの特性が得られることを確認した。 |
(英) |
The miniaturization of OMT (Ortho-Mode-Transducer) is one of the development issues in antenna feed systems for satellite communications. Here, we propose a configuration that achieves both miniaturization and good characteristics in an OMT having a circular waveguide common terminal that transmits two orthogonal linear polarizations, a rectangular branch terminal that separates linear polarization in the high frequency band in the axial direction, and another rectangular branch terminal that separates linear polarization in the low frequency band in the perpendicular direction. The proposed configuration converts a circular waveguide into a cross-shaped waveguide. The axial branch terminal transforms the cross section of the cross-shaped waveguide into a stepped shape, and the perpendicular branch terminal is located to straddle the circular waveguide and the cross-shaped waveguide. It is miniaturized by being directly connected so as to straddle the conversion unit and transforming within the cross section of the cross-shaped waveguide. Furthermore, by arranging the axial branch terminal offset from the center of the common terminal to the perpendicular branch terminal side, the influence of the proximity arrangement of the metamorphic part is compensated and good characteristics are realized.
The proposed configuration was designed in the low frequency bandwidth 12.9% and the high frequency bandwidth 3.5% and prototype was evaluated using a 3D printer (aluminum alloy with low Si content). The design results and measurement results generally matched. Reflection of 25 dB, isolation of 30 dB, XPD of 30 dB and loss of 0.1 dB were obtained. |
キーワード |
(和) |
アンテナ給電回路 / 導波管 / 偏波分離回路 / 3Dプリンタ / / / / |
(英) |
Antenna feed systems / Waveguide / OMT / 3D-printer / / / / |
文献情報 |
信学技報, vol. 123, no. 35, MW2023-17, pp. 43-48, 2023年5月. |
資料番号 |
MW2023-17 |
発行日 |
2023-05-11 (MW) |
ISSN |
Online edition: ISSN 2432-6380 |
著作権に ついて |
技術研究報告に掲載された論文の著作権は電子情報通信学会に帰属します.(許諾番号:10GA0019/12GB0052/13GB0056/17GB0034/18GB0034) |
PDFダウンロード |
MW2023-17 |