講演抄録/キーワード |
講演名 |
2012-11-29 15:00
直管型熱音響エンジンにおける全長及び内径が発振条件に与える影響 ○柳本浩平(同志社大)・坂本眞一(滋賀県立大)・中野陽介・柴田健次・高原教揮・渡辺好章(同志社大) US2012-75 |
抄録 |
(和) |
熱音響システムは地球環境に配慮した新たなシステムとして期待されている.しかし,自励振動の開始温度(発振温度比)が高いという課題が存在する.熱音響システムの発振温度比を小さくできれば,広い温度帯でこのシステムが活躍することが期待できる.そこで本報告では,円筒管の全長及び内径に着目し,これらを変更した際の発振温度比に与える影響を検討した.流路半径0.55 mm,長さ50 mmのスタックを円筒管内に設置し,直管型熱音響エンジンを構成した.そして,内径が24 mm,42.5 mm,95.6 mmの円筒管を用い,全長を1200 mmから3750 mmまで5点変更し,実験を行った.測定の結果,全ての内径において,発振温度比の分布に同じような傾向が見られた.しかし,各内径における最低発振温度比を示す熱交換の様子を表す値は異なっていた.これは,発振条件を満たす温度比がシステム全体での散逸量の影響を受けたためであると考えられる. |
(英) |
The thermoacoustic systems are expected as new system which considered global environment. However, they have disadvantage that the start temperature of a self oscillation (onset temperature ratio:OTR) is high. If OTR can be made small, these systems are expected to be used in wide range of temperature. In this report, we examined the effects of changing the full length and the inner diameter of a cylindrical tube on OTR. The straight-tube-type thermoacoustic engine with a stack which has 0.55 mm in pore radius and 50 mm in length was consisted. And, experiments were conducted by using the cylindrical tubes of 24 mm, 42.5 mm, and 95.6 mm in the inner diameter and changing five full lengths from 1200 mm to 3750 mm. In all inner diameters, the same tendency in distribution of each OTR was confirmed at the results of measurements. However, the values describing heat exchange which showed the minimum OTR in each inner diameter differed. The temperature ratio met oscillation condition was affected by the amount of loss in the whole system. |
キーワード |
(和) |
熱音響現象 / 全長 / 内径 / 発振条件 / 発振温度比 / / / |
(英) |
Thermoacoustic phenomena / Total length / Inner diameter / Oscillation condition / Onset temperature ratio / / / |
文献情報 |
信学技報, vol. 112, no. 326, US2012-75, pp. 31-34, 2012年11月. |
資料番号 |
US2012-75 |
発行日 |
2012-11-22 (US) |
ISSN |
Print edition: ISSN 0913-5685 Online edition: ISSN 2432-6380 |
著作権に ついて |
技術研究報告に掲載された論文の著作権は電子情報通信学会に帰属します.(許諾番号:10GA0019/12GB0052/13GB0056/17GB0034/18GB0034) |
PDFダウンロード |
US2012-75 |