講演抄録/キーワード |
講演名 |
2018-03-02 13:35
直流高電圧のアーク放電に対する磁束密度の影響 ○梅澤 翼・森田暁也・澤 孝一郎・吉田 清(日本工大) EMD2017-59 エレソ技報アーカイブへのリンク:EMD2017-59 |
抄録 |
(和) |
近年,太陽光発電や電気自動車(EV)など,直流高電圧,大電流を使用する機器が増加している。回路を確実に遮断するのが電気接点(コンタクト)の役割である。直流のアーク放電を消弧させるために,磁界を用いた磁気吹き消しと呼ばれる方法が広く用いられている。今回は,磁束密度を1.2~150mTの範囲で変化させ,電源電圧は直流の100, 300, 500Vとし,電流は10A一定に設定した。接点の開離速度は10mm/s,50mm/s,100mm/sの3通りとし,接点素材はW(タングステン)で実験を行った。アーク放電の電圧・電流波形や電力波形から,アーク継続時間やアークエネルギーを求めた。その結果,アーク継続時間は,磁束密度の増加に対して反比例に近い関係を示すことがわかった。また,磁束密度は10mTでアーク継続時間を80%以上減少させることがわかった。 |
(英) |
Solar power generation and electric vehicles (EV) that use high current with high DC voltage are increasing. The role of electrical contacts to reliably shut off the DC power supply circuit is important in such systems. In order to extinguish the DC arc discharge, a method called "magnetic blow-out" by a magnetic field is widely used. In the experiment, the magnetic flux density was varied in the range of 1.2 to 150 mT, the source voltage was DC 100, 300, 500 V, and the current was set to 10 A constant. The opening speed of the contact is three patterns of 10, 50, 100 mm/s. And, the contact material is tungsten. Arc duration and arc energy were obtained from the voltage / current waveform and power waveform of the arc discharge. As a result, the arc duration was almost inversely proportional to the increase in magnetic flux density. Furthermore, the arc duration was reduced by 80% or more with a magnetic flux density of 10 mT. |
キーワード |
(和) |
アーク放電 / アーク継続時間 / 電気接点 / 開離時アーク / 磁束密度 / 磁気吹き消し / タングステン / |
(英) |
Arc discharge / Arc duration time / Electrical contact / Break arc / Magnetic flux density / Magnetic blow / Tungsten / |
文献情報 |
信学技報, vol. 117, no. 467, EMD2017-59, pp. 9-12, 2018年3月. |
資料番号 |
EMD2017-59 |
発行日 |
2018-02-23 (EMD) |
ISSN |
Print edition: ISSN 0913-5685 Online edition: ISSN 2432-6380 |
著作権に ついて |
技術研究報告に掲載された論文の著作権は電子情報通信学会に帰属します.(許諾番号:10GA0019/12GB0052/13GB0056/17GB0034/18GB0034) |
PDFダウンロード |
EMD2017-59 エレソ技報アーカイブへのリンク:EMD2017-59 |