講演抄録/キーワード |
講演名 |
2010-10-28 13:00
ニオブ酸カリウム/チタン酸バリウム複合材料の開発 ○臼井亮輔・番場教子(信州大) CPM2010-91 エレソ技報アーカイブへのリンク:CPM2010-91 |
抄録 |
(和) |
本研究では、ニオブ酸カリウム(KN)セラミックスの問題点である耐水性と焼結性の改善を目指し、チタン酸バリウム(BT)との複合化を試みた。その結果、KNとBTが相互に固溶した固溶複合体となることで耐水性の改善、焼結性の向上が確認できた。しかし、十分な密度を得られなかったことから、更に2つの手法を試みた。1つめはKN粉末の粒径を小さくするためのKN仮焼温度の変更であり、2つめは、K-richなK1.005NbO3 (K1.005N)を母材に用いた複合体の作製である。仮焼温度を1000℃から800℃に変更した場合、最終的な相互固溶量及び密度の減少が見られた。K1.005N を用いた場合、KNに比べ焼結性は向上したが、十分な密度を得ることはできなかった。しかし、作製条件により特性を制御、向上できる可能性が見出された。 |
(英) |
Potassium niobate (KN)/ barium titanate (BT) composites were fabricated
by normal sintering in order to improve water-resistance, sinterability
and piezoelectric properties of KN ceramics in this work. Consequently,
water-resistance and sinterability of KN/BT composites were improved
compared with KN monolith. These are considered that KN and BT form
solid solution with each other. However, since the density of the
composites was not sufficient, 2 another methods were attempted. One was
change of calcination temperature for synthesizing KN, and the other was
using K1.005 NbO3 (K1.005 N) as a matrix instead of KN. When the
temperature changed from 1000℃ to 800℃, the decrease of amount of
BT which formed a solid solution with KN and the density were confirmed.
In the case of using K1.005 N powder, sinterability improved, but the
density was still not enough. However, the possibility that the
characteristic of KN/BT ceramics could be controlled and improved by
preparation process was able to be shown. |
キーワード |
(和) |
ニオブ酸カリウム / チタン酸バリウム / 複合体 / 固溶体 / / / / |
(英) |
Potassium niobate / Barium titanate / composites / solid solution / / / / |
文献情報 |
信学技報, vol. 110, no. 261, CPM2010-91, pp. 1-5, 2010年10月. |
資料番号 |
CPM2010-91 |
発行日 |
2010-10-21 (CPM) |
ISSN |
Print edition: ISSN 0913-5685 Online edition: ISSN 2432-6380 |
著作権に ついて |
技術研究報告に掲載された論文の著作権は電子情報通信学会に帰属します.(許諾番号:10GA0019/12GB0052/13GB0056/17GB0034/18GB0034) |
PDFダウンロード |
CPM2010-91 エレソ技報アーカイブへのリンク:CPM2010-91 |